Kavassuplast Asphaltomastic Membrane is a polymer modified plastomeric waterproofing screed layer manufactured to highest International standards. Kavassuplast Asphaltomastic Membrane is a five layer pre fabricated mastic screed, in which center core is of high Molecular high density non woven polyester mat (Manufactured in Italy), center core is the heart of Kavassuplast Asphaltomastic Membrane in which Top & bottom layer is consisting of Polyethylene sheets which is a complete barrier against incursion of water & moisture. The center core is protected on both sides with polymer modified Asphaltic mix, which has high penetration, high heat resistance and much higher softening point asphalt mix. Shaliplast Asphalto-mastic Membrane also achieves good bonding with wooden, concrete & steel substrate and create a strong adhesion between overlap joints. In turn, Shaliplast Asphaltomastic Membrane is protected on the top & bottom with thermofusible HMHDPE sheet which act as an extra waterproofer to reinforce the non permeable quality of the entire mastic sheet. The resultant Shaliplast Asphaltomastic Membrane has very good elongation to absorb all structural movements, point loads etc. With high tensile strength, the Shaliplast Asphaltomastic Screed is still extremely flexible and pliable to adapt to contours. For these reasons Shaliplast Asphaltomastic Membrane makes an ideal waterproofer. Shaliplast Asphaltomastic Membrane is available in 3, 4 & 5mm thickness.
Heavy Duty Polymer Modified Mastic Membrane
For Bridge Slab Waterproofing:
Application of Shaliplast Asphaltomastic Membrane is extremely fast and easy. Smooth surface with minimum slope is required to apply Shaliplast Asphaltomastic Membrane. The concrete surface is first cleaned to eliminate all sharp projections. After cleaning Suitable primer such as Shalimar Bitumen Primer is then coated @ 400 Gms/ Sqm over the surface. After drying of primer Shaliplast Asphaltomastic Membrane is unrolled over the primed surface (with overlaps of 7.5 – 10 cm) by and bonded completely by thermofusing bottom layer of HMHDPE by isobutane torch. The overlaps joints are then thermofused by isobutane torch flame. Special care is taken at singularities such as drains, expansion joints etc. More details of application are available in application Guide. Shaliplast Asphaltomastic Membrane acts as seamless water barrier over the concrete surfaces & base screed before laying of bituminous concrete in flexible pavements.
For Waterproofing of concrete Superstructures, Sub ways slabs, Cellar floors, Concrete Floor, Watertanks, Bridge deck slab, Box Culverts , Minor & major Bridge Slabs and over wearing coarse,Tunnel retaining walls, underground sumps & water retaining concrete reser- voirs. Shaliplast Asphaltomastic Membrane acts as seamless water barrier just before laying of bituminous concrete in flexible pavements.
- Description
Kavassuplast Asphaltomastic Membrane is a polymer modified plastomeric waterproofing screed layer manufactured to highest International standards. Kavassuplast Asphaltomastic Membrane is a five layer pre fabricated mastic screed, in which center core is of high Molecular high density non woven polyester mat (Manufactured in Italy), center core is the heart of Kavassuplast Asphaltomastic Membrane in which Top & bottom layer is consisting of Polyethylene sheets which is a complete barrier against incursion of water & moisture. The center core is protected on both sides with polymer modified Asphaltic mix, which has high penetration, high heat resistance and much higher softening point asphalt mix. Shaliplast Asphalto-mastic Membrane also achieves good bonding with wooden, concrete & steel substrate and create a strong adhesion between overlap joints. In turn, Shaliplast Asphaltomastic Membrane is protected on the top & bottom with thermofusible HMHDPE sheet which act as an extra waterproofer to reinforce the non permeable quality of the entire mastic sheet. The resultant Shaliplast Asphaltomastic Membrane has very good elongation to absorb all structural movements, point loads etc. With high tensile strength, the Shaliplast Asphaltomastic Screed is still extremely flexible and pliable to adapt to contours. For these reasons Shaliplast Asphaltomastic Membrane makes an ideal waterproofer. Shaliplast Asphaltomastic Membrane is available in 3, 4 & 5mm thickness.
- Application Procedure
For Bridge Slab Waterproofing:
Application of Shaliplast Asphaltomastic Membrane is extremely fast and easy. Smooth surface with minimum slope is required to apply Shaliplast Asphaltomastic Membrane. The concrete surface is first cleaned to eliminate all sharp projections. After cleaning Suitable primer such as Shalimar Bitumen Primer is then coated @ 400 Gms/ Sqm over the surface. After drying of primer Shaliplast Asphaltomastic Membrane is unrolled over the primed surface (with overlaps of 7.5 – 10 cm) by and bonded completely by thermofusing bottom layer of HMHDPE by isobutane torch. The overlaps joints are then thermofused by isobutane torch flame. Special care is taken at singularities such as drains, expansion joints etc. More details of application are available in application Guide. Shaliplast Asphaltomastic Membrane acts as seamless water barrier over the concrete surfaces & base screed before laying of bituminous concrete in flexible pavements.- Uses
For Waterproofing of concrete Superstructures, Sub ways slabs, Cellar floors, Concrete Floor, Watertanks, Bridge deck slab, Box Culverts , Minor & major Bridge Slabs and over wearing coarse,Tunnel retaining walls, underground sumps & water retaining concrete reser- voirs. Shaliplast Asphaltomastic Membrane acts as seamless water barrier just before laying of bituminous concrete in flexible pavements.
Shalimar’s Kavassuplast Asphaltomastic
Tender Schedule:
Supplying and Fixing water proofing treatment with APP modified polymeric waterproofing membrane of 3mm, 4mm & 5mm thickness. KAVASSUPLAST ASPHALTOMASTIC MEMBRANE consisting of center core as per requirement of technical specification printed overleaf of this literature. Reinforcement including coating the surface with Shalimar Bitumen primer and torch application of membrane with 10cms Overlaps where required.
National Award Winner
| Characteristics | Units | Requirements | Requirements |
| Softening point | °C | Min 150 °C | Min 150 °C |
| Penetration at 25 °C,100g 5 sec,1/10mm | mm | 5-25 mm | 5-25 mm |
| Centre Core Reinforcement | gms./ sq.mtr. | Non woven Polyester mat 160 Gms./Sqm. | Non woven Polyester mat 160 Gms./Sqm. |
| Pliability | °C | Min +10 °C Max 0°C & -5°C for hilly region Does not break | Min +10 °C Max 0°C & -5°C for hilly region Does not break |
| Heat resistance 10×10 cm Test Piece Hung Vertically | °C | Does not drip At 120°C | Does not drip At 120°C |
| Tensile strength Longitudinal Transverse | N/5 cm | 500> N/5 cm 300> N/5 cm | 500> N/5 cm 300> N/5 cm |
| Elongation Longitudinal Transverse | % | Min. 45% Min. 50% | Min. 45% Min. 50% |
| Dimensions (packing) | mtr. | 1m x 15m | 1m x 15m |
| Weight. | kg./m² | 3.8 kg + 5% | 4.6 kg + 5% |
| Thickness | mm | 3.00 + 0.05 | 4.00 + 0.05 |
LPG butane torch & roller for pressing membrane uniformly.
AS PER ISO 9001 : 2008
- Technical Data
Characteristics Units Requirements Requirements Softening point °C Min 150 °C Min 150 °C Penetration at 25 °C,100g 5 sec,1/10mm mm 5-25 mm 5-25 mm Centre Core Reinforcement gms./ sq.mtr. Non woven Polyester mat 160 Gms./Sqm. Non woven Polyester mat 160 Gms./Sqm. Pliability °C Min +10 °C
Max 0°C & -5°C for hilly region Does not break
Min +10 °C
Max 0°C & -5°C for hilly region Does not break
Heat resistance 10×10 cm Test Piece Hung Vertically °C Does not drip At 120°C Does not drip At 120°C Tensile strength Longitudinal Transverse N/5 cm 500> N/5 cm
300> N/5 cm
500> N/5 cm
300> N/5 cm
Elongation Longitudinal Transverse % Min. 45%
Min. 50%
Min. 45%
Min. 50%
Dimensions (packing) mtr. 1m x 15m 1m x 15m Weight. kg./m² 3.8 kg + 5% 4.6 kg + 5% Thickness mm 3.00 + 0.05 4.00 + 0.05 - Application Equipment
LPG butane torch & roller for pressing membrane uniformly.
- Quality Assurance
AS PER ISO 9001 : 2008
What Clients Say
Crystallomix-PG/PGS
The Performance Of “SHALIMAR’S KAVASSU CRYSTALLOMIX-PG/PGS (CRYSTALLINE ADMIXTURE) in our Six Lane Of Davangree Haveri Road Project found Good With 12-13% More Strength.
Rainsta Patch
Shalimar’s Kavassu Rainsta patch filler used in Hyderabad-Karimnagar-Ramagundam Road Project (HRK), SH-1 performed well and found very good.
Curex
Shalimar’s Kavassu Curex used in Construction of 4/6 Lanning of Pune –Satara Toll Road Project- Package-3 found excellent.
Admixture
Shalimar’s Kavassu Plast SP-431(Admixture) Used in construction of Nehru Outer Ring Road Expressway,Hyderabad in the state of Andhra Pradesh,India found very good.
